CalaisTurbo New Tags
User Name: Password:

Go Back   calaisturbo.com.au > For Sale & Wanted > For Sale & Wanted - VL - Turbos ONLY
GRUNT Performance

Reply

 

Thread Tools
Old 02-06-14, 00:58   #1
JNRVLT
Player
 
JNRVLT's Avatar
 
Join Date: 03-07-06
Location: VIC, North
Car:
Trader Rating: (1)
[FS - VIC] bt1 big build project ($30k neg)

For Sale? Or Wanted?
FS
Price/Amount
30k neg
Open to Swap?
Maybe
State
VIC
Short Description for title?
bt1 big build project
Genuine Turbo Motor? A8?
Yes
Transmission?
MANUAL
Currently Registered?
Yes
REGO/VIN Number?
club permit
Contact Info Other than this Forum?
0439370561
Description[INDENT] selling bt1 big build project car

--------------------------------------------------------------------------------

unfortunately I have come to the conclusion that I have to part with my wild bt1 build as I cannot afford to keep going its a genuine vl bt1 with everything new and never used I will try detail this add as best as possible for the work and parts. This car has had no corners cut and countless hours and money spent on it. Will suit the most fussiest of buyers. Please only enquire if your genuine and for the price if you don’t like it good on ya don’t read no more as anyone who knows about building a vl will know that I have spent three times the amount of what im asking,
fully resprayed bt1 with no rust immaculate paint job, full deleted and smoothed engine bay was originaly a mulberry nsw detective car very rare factory mx7. Repainted in a custom purple with matt grey bars
all new moulds, bars, lights, rubber seal kit, boot strips garnish etc
here goes:
engine:
brand new Kanaris engine combo (Still has not been started) genuine buyers can get meet with James and get every detail of the build and specs engine was build for the car to run in the 9s.

-full prepped, balanced machined blueprinted acid bathed etc
-mahle special coated full forged pistons and rings 1000hp rated
-manley h beam rods 1500hp rated
-linished and machined crank
-Arp fastner kit throughout whole engine mains, head, rods etc
-acl race bearings
-gtr oil pump with added reimax billet oil pump gears
-all brand new water pump pulleys housings hoses lines etc
-large oil pan
engine was built to comfortably handle 800hp

head:
full race prepped head
-ported and polished
-stainless valves
-crow springs
-crow cam Kanaris engines grind
-adjustable rocker gear with rocker cover spacer
-rollmaster adjustable cam gear
-new cambelt tensioners etc
-JPC plenum
-holley billet throttle body
trans:
fully built 2 speed glide
-bm pan
-billet internals
-tce 8" converter
-tci trans brake
-quicksilver shifter
all new billet internals new clutches etc
-machined pump
-bell housing adapter
-new starter
Hot side
Custom built JPC garret 1000 roller bearing turbo with 35/40 external housing to get it up on boost friendlier
Custom built steampipe kanaris engines manifold
Turbosmart powergate 50mm wastegate

Diff
1000km old rebuilt borg warner diff 28spline axels, lsd fresh, tight 3:7 gear ratio
Suspension
King springs all round
Pedders 90/10 shockers
Pedders sport in rear
Boxed control arms
New bearing plates, control arms and bushes throughout whole car

Brakes
All new bendix ultimate pads all round, new rear rotors, vt brake upgrade on the from with new slotted rotors
Brand new brake master and booster
Fuel system
JPC fuel rail/Rochester 1000cc injectors
All new hard lines run up the body -8 feed -6 return
X2 genuine bosch o44 fuel pumps through a 2l surge tank to billet filter
All lines are braided with proflow/aeroflow fittings
Proflow fuel reg
Walbro intank
Electrical
Brand new microtech lt16 with 45psi internal map sensor with new loom and connectors
Brand new complete ice ignition kit coil leads booster
New dizzy
Alternator
Sensors
Eboost 1
Battery relocated to boot
Hidden wiring
Interior
Beige restored dash
Immaculate beige bt1 seats and door trims
Custom beige suede headlining
All new sound deadener
Pioneer headunit
Aftermarket alarm
4 point bolt in roll cage with from harnesses

Cooling
New alloy radiator
Intercooler 100mm thick
Davis craig 17’ thermo
Overflow/catch can

I have probably missed a lot more parts but everything that I have will be going with the car all that needs doing is dump pipe to be made then just a tune and its ready for the track please only genuine enquiries. The money has been spent in all the right places with no corners cut. Have all receipts and evidence of all the work taken out on the car. The attention to detail on it is unbelievable as im a very fussy person.
Asking $30,000 neg
Thanks
Stefan 0439370561
__________________
munch munch munch eat v8s for lunch

Last edited by JNRVLT; 02-06-14 at 01:43.
JNRVLT is offline   Reply With Quote
Old 02-06-14, 01:57   #2
JNRVLT
Player
 
JNRVLT's Avatar
 
Join Date: 03-07-06
Location: VIC, North
Car:
Trader Rating: (1)
pics

pics
Attached Images
 
__________________
munch munch munch eat v8s for lunch
JNRVLT is offline   Reply With Quote
Old 29-06-14, 17:10   #3
7heavn
Player
 
Join Date: 02-06-10
Location: NSW, sydney
Car:
Trader Rating: (0)
Hi mate I sent you a pm.
7heavn is offline   Reply With Quote
Old 29-06-14, 18:41   #4
brabus
Player
 
Join Date: 03-07-11
Location: Melbourne, western suburbs
Car: e430 mercedes , yellow vlt bt1 [sspect]
Trader Rating: (0)
Pics won't load could you email me then to sk_cz@hotmail.com
.
brabus is offline   Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time now is 09:28.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Ad Management plugin by RedTyger